Call Today

 

How do you really feel about A Step-by-Step Guide to Installing a Bathtub?

Setting up a bathtub isn't specifically brain surgery, but it does call for solid plumbing, carpentry, as well as in some cases, tiling skills. Changing an old tub with a new one is likewise a reasonably tough job. If the old bathtub is easily easily accessible, the job can move immediately; if you have to open a wall to get rid of the old bathtub as well as position the brand-new tub, the task is a lot harder. In either instance, the job is within a home handyman's abilities, although you will need an assistant to move out the old tub and also embeded in the brand-new one. Ensure you have actually certified yourself for the job and also fit attempting it. As opposed to employing a specialist to take over a halfway-completed task, it is much better to consider using one before you start. Possibilities are you might need a professional plumber to make tube connections.
This article will certainly help you set up a brand-new tub in your washroom if you have currently bought a new tub as well as do not need to alter the plan of your previous water system pipes.
Your devices and also material checklist should make up the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Removing Old Taps

If you need to change old taps with new ones as a part of your installation, then the first thing you need to do is detach the water system. After doing so, turn on the faucets to drain any type of water staying in the system. The procedure of eliminating the existing faucets can be fairly bothersome because of the limited gain access to that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a towel prepared for the staying water that will certainly come from the pipes. Once the supply pipes have actually been removed, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Prior to proceeding to fit the new taps, contrast the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.

 

 

Suitable New Taps

If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end provides a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the installing opening in the bath/basin making sure that the washing machines are in place in between the faucet and the sink. Protect the tap in position with the supplier offered backnut. When the faucet is firmly in place, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former type must be attached to the tap finishes initially, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.

 

 

Setting up the Bath tub

Utilizing the two wood boards under its feet, place the tub in the required placement. The wooden boards are useful in uniformly spreading out the weight of the bathtub over the location of the boards instead of focusing all the weight onto four little factors.
The next goal is to make sure that the bathtub is leveled all round. This can be attained by examining the spirit level and adjusting the feet on the tub up until the level reviews degree.
To set up faucets, fit the bottom of the furthest adaptable tap adapter to the ideal supply pipeline by making a compression join; after that do the exact same for the other faucet.
Turn on the water system and also examine all joints and brand-new pipework for leaks and tighten them if necessary. Fill the bath tub and additionally examine the overflow outlet as well as the regular outlet for leaks.
Finally, deal with the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the bathtub ought to wait up until the bathtub has actually been made use of a minimum of once as this will settle it right into its final position.

 

 

Getting ready for the Installation

Firstly, the supporting frame supplied with the bath needs to be fitted (if needed) according to the producer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to see to it that if the tap includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to prevent strain on the bathtub.
Fit the flexible faucet connectors to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you use every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its final placement.

 

 

Tiling Around the Tub

In the location where the bathroom fulfills the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to crack an inflexible seal, triggering the water to penetrate the wall surface in between the bathroom and also the tiling, leading to issues with moisture and feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealers to blend in your fixtures and also installations. They are marketed in tubes and also cartridges, and are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill up the tub with water before securing, to permit the activity experienced when the tub remains in use. The sealer can break relatively very early if you do not take into consideration this activity before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or waterproof glue and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I am very taken with A Step-by-Step Guide to Installing a Bathtub and I'm hoping you appreciated the article. Feel free to take the time to promote this page if you enjoyed reading it. I thank you for reading our article about How to Install a Bathtub Yourself.

Preventative solutions offered.